|
#EX-501-3E,
Duration: 3 days of hands-on ExperTune training
Class Schedule
Register Me
Three days of hands-on ExperTune training. Includes case studies of
industrial problems and solutions.
Objectives:
Master the techniques of optimizing process loops. Learn how to
effectively use ExperTune's PID Tuning and analysis tools in your
plant.
Who should attend:
Anyone with a basic knowledge of instrumentation who wishes to use
loop analysis and optimization software with PID controllers.
Content:
Day 1: Fundamental concepts
Introduction
- Control loops
- Noise, disturbances, load
- Feedback-Feedforward
- Control objectives
Process
- Simple model
- Types of processes
- Process flaws
- Exercises
Controllers
- Proportional, integral, derivative, filter
- Structures of industrial controllers
- Exercises
Tuning
- Intuitive tuning
- Performance criteria
- Load change, Setpoint change
- Tuning: a compromise
- Traditional tuning methods
- Natural frequency
- Importance of time delay
- Limits of traditional tuning methods
- Exercises
Day 2: Tuning
and analysing a loop using ExperTune
Frequency
domain vs. time domain, an introduction
- Definitions
- Terminology
- From the time
domain to the frequency domain
ExperTune software
- Basic principles
- Acquiring the data
- Frequency analysis, time series
- Choice of tuning objectives
- The tools available
- Bode plot, how to interpret it
- Exercises
Data to tune a loop
- Good data, from a controller output change (Manual)
- Good data, from a setpoint change (Automatic)
- Exercises
Tuning control loops using ExperTune
- PID grid
- Quality of frequency data
- Filter
- Selecting tuning parameters, Safety factor, Lambda value
- Load rejection and setpoint tuning
- Tuning comparison with Lambda and Ziegler/Nichols tuning
- Simulation, response to load change, setpoint change, noise
- Frequency response
- Robustness plot
- Performances: IAE, robustness, valve travel, …
- Simulator
- Exercises
Analysing a control loop using ExperTune
- Hysteresis check
- Characterization, Linearization
- Cross correlation analysis
- Power spectral density
- Statistical analysis
- ISO 9000 and reporting
- Exercises
Day 3: Using ExperTune efficiently
Steps to
tune a loop
- Bump sizes,
preliminaries, operator cooperation
- Setpoint
changes in both directions
- Bump tests to
check hysteresis, stiction, linearity
- Loop
analysis, design, 4 rules of 3
- Exercises
Analyzing
the data from a test in automatic mode
- How to detect
hysteresis, stiction, high process gain
- How to detect
bad tuning parameters
- Exercises
- Tips and
tricks
Analyzing control loops using ExperTune tools
- Hysteresis, noise and process gain check
- Stiction test
- Characterization, Linearization
- Statistical analysis, Power spectrum
- Exercises
Scan time
- Aliasing
- ExperTune and scan time to acquire data
Exercise: real cases, self regulating and integrating processes
- Analyzing the data
- Editing the data
- Tuning the loop to quickly remove disturbances
- Robustness analysis
Reporting
- ExperTune report
- Adding items to report
Tuning multi loops system
- Tuning interactive loops
- Synchronizing loops
- Tuning a cascade system
- Exercises
Conclusions
- Tuning methods comparison
- Time to tune loops
- Robustness and performance
- Practical rules, tips and tricks
- Process control and economics
Software Used
- ExperTune
(latest version)
All training is presented by: ExperTune's Official Training
Partners. Our partners are highly trained and have
extensive field experience. The average instructor has over
20 years' experience in process control.
|
"Instructor was expert in theory and fieldwork, which is seldom seen." I&C Training, Entergy
"Great class & well worth the $ ... Discussion of real life problems & seeing
real life data." Process Engineer, Armstrong World
"One of the best instructor's I've seen." PC&E technician,
Boise
"Very good course," Manager Internal Training, Siemens
"It was a very useful training that covered the practical aspect of control theory,"
Validation Engineer, Merck, Sharp & Dohme
"This time Process Control theoretical principles really got a practical sense!"
Controls & Computer Validation Engineer, Merck & Co.
"This course was very well done in all aspects,"
Systems Technician, Placid Refining
"Very good course, it is a well balance between theory and practice,"
Control Engineer, ECOPETROL - ICP
"I would highly recommend this course to anybody in the process industry,"
Instrument Tech, Terra Nova
"Excellent Course - Great Instructor. Covered material & reviewed
course Materials very well. Good Text Books - Covered Basics to
greater Details. I Have no Complaints. Would like to attend
Troubleshooting course sometime later,"
Process Optimization Specialist, Weyerhaeuser
"I feel that the info will pay for course with first solution,"
Control System Engineer, Weyerhaeuser
"I learned a considerable amount regarding loop tuning and control in general,"
Process Controls Eng., Abitibi Consolidated Inc.
"I plan to utilize what I have learned from Top Control and combine
that with the power of ExperTune to help place our process back on
track. I am always looking for ways to save a penny and this should
save a lot of money by increasing the performance of our loops,"
Process control engineer, Cargill Inc.
"This training made me realize just how important it is to do a preventive
analysis on loops in order to avoid working in the dark and to optimize the
work of our technicians,"
Supervisor Electricity/Instrumentation, Kruger Inc.
"An excellent class that tied all the basics of PID tuning together.
I had all the tools, software and great controllers, but I wasn't
necessarily using them properly. Now I will,"
Engineer, Bicron
"Usually a class like this isn't extremely useful, but this class
is the exception. One of the few classes I truly enjoyed,"
Process Control Engineer, Noltex
"I learned a lot and really found the course to be helpful. Abbott
labs will benefit tremendously from this class,"
Utilities,Abbott Labs
"Very good class for a very good piece of software,"
Control's Designer, IBM
"Overall good class,"
Control Engineer, Designer, IBM
"The course content was directed to the concerns and areas of interest of the attendees. Analysis of actual in-house processes was included during the training,"
Engineer, VLOC
"George did an excellent job relating crystal growth to the PID
tuning with ExperTune. I learned a lot and can find this product/course
quite useful to further developing my laboratory,"
Production Growth Engineer, VLOC
"It is an excellent course,"
Chief Engineer, Yokogawa Corp of America
"I thought this course was very informative with a lot of useful information. I look forward to the advanced course,"
Operations, Air Products
"I found this class to be extremely practical and useful. It had a
good combination of theory and empirical information. We had several of our
top process controls guys in this class and you really showed your expertise,"
Lead Project Engineer, Siemens
"Very good course. Info. was related very well. An excellent
time saving tool," Instr. Tech, Petro-Canada
"This was the best exposure/training I have attended in terms of
practical application. The best value added I have attended in many
years," Inst. Tech. (FPSO), Petro-Canada.
"Excellent course - very interesting & bound to be one of the
best & most widely used tool on the Terra Nova FPSO,"
Instrumentation - Ops, Terra Nova Alliance
"Excellent course & would be of value to me during my job. Would
like to take a course on the optimization of the plant utilizing this
tool," Process Engineer, Petro-Canada
"A great overview of both ExperTune Software and tuning (PID)
loops. I'm excited to get back and get more performance & less wear
out of my process," Consulting Engineer, Johnson Polymer
"This has been the best course involving tuning and process
control that I have taken. The software and knowledge will be able
to be applied at the smelter in a practical approach to achieve
better control. I would recommend this course to anyone who works in
a plant and has to tune loops," Senior Process Control
Engineer, Kennecott Utah Copper
"Learned a lot in a small amount of time. Many light bulbs came
on during class," Regional Engineer, Sanitary Water Group
"Very pleased with course content and practical application,"
Senior Project Engineer, Johns Manville
"The course gave me a lot of insight and strategies to attack tuning issues in our plant."
Instrumentation Tech, Weyerhaeuser Company
"Excellent class with a very knowledgeable and excellent instructor and a very good product."
Process Control , Wellman Inc
"This class has a very high gain!!"
Control Systems Engineer, Kennecott Utah Copper
"I really enjoyed this class. As someone who recently purchased
ExperTune, this class has taught me good optimization techniques that
will help me in getting the most out of our investment. Without this
class, I'm sure I would have under utilized the software. Thanks for
setting this up!"
Staff Electrical Engineer, Armstrong World Industries, Inc.
"The course was very well presented. Good mixture of book
and hands on training. Hank was able to relate a lot of his field
experience to classroom examples. Best tuning class that I have
attended."
Instrument Foreman, PSNH Schiller Station
"The software is a very powerful and valuable tool. The training
compliments the software and greatly increases the overall value. The
training is enhanced by the fact that TOP Control field experts
provide the instruction and give real-life examples and understand the
issues that the students are faced with."
Process Control, Wellman, Inc
"Excellent course with tons of practical application for any plant!"
Senior Engineer, Johnson Polymer
"Very good course. Instructor has field experience and teaching experience
and conveys information very well with real life examples." Control Systems
Engineer, Precision Engineering
|
